Damascus Steel Billet 22cm Water Wave Pattern – DIY Knife Making

Damascus Steel Billet – Water Wave Pattern | 22 × 3 × 0.3 cm

Craft your next heirloom-quality blade with this beautifully forged Damascus steel billet. Featuring a striking water-wave sandwich pattern, this blank bar is the ideal starting point for knife makers of all skill levels — from hobbyists to seasoned bladesmiths. Made in Mainland China.

Key Specifications

• Material: Alloy Damascus Steel (multi-layer forged)
• Dimensions: Length 22 cm × Width 3 cm × Thickness 0.3 cm
• Hardness: Approx. HRC 58 (vacuum deep-cooling & heat-treated for balanced sharpness and toughness)
• Surface Finish: Pre-flat-ground & acid-pickled for a refined starting surface
• Pattern: Water Wave / Sandwich layered Damascus
• Model: DIY-22

Why Choose This Billet?

• ✅ Ready-to-work surface — flat-ground and pickled, giving you ~1.5× more usable material compared to un-ground stock
• ✅ Balanced hardness (HRC 58) — achieved through vacuum deep-cooling and heat treatment, combining edge retention with toughness
• ✅ Stunning natural pattern — each billet has a unique water-wave texture that emerges beautifully through acid etching
• ✅ DIY-friendly — suitable for custom knife making, blade blanks, and craft projects

Important Notes

• Due to the hand-forging process, dimensional tolerances are: ±1–3 mm (length/width) and ±0.1–0.2 mm (thickness).
• Pattern stickers on both sides may vary slightly in thickness and texture due to the layered segmenting process.
• A secondary acid-cleaning step is recommended after final shaping and edge grinding.
• Flat grinding removes at least 0.5 mm from each side — factor this into your design.

Acid-Pickling Guide

1. Polish your blank to 600-grit or higher (aim for a near-mirror finish with no visible scratches under light).
2. Mix acid solution at a 1:4 ratio (acid to water); adjust between 1:3 and 1:5 depending on material and desired depth.
3. Submerge for approximately 1 minute, check the pattern depth, and repeat in short intervals as needed.
4. Rinse thoroughly with water, then neutralize with dish soap to stop the etching process.
5. Polish, buff, and apply a light coat of oil to maintain the finish and protect the steel.
6. Seal the acid solution tightly when not in use to prevent degradation.

Related Products You May Like

Complete your workshop setup with these popular tools and accessories:

• Bincoo Solid Wood Walnut Bean Scoop – Precision Craft Tool
• 2.3m Flexible Cleaning Brush – Versatile Detail Tool

Learn more: OSHA on personal protective equipment

Frequently Asked Questions

Q: Is this Damascus steel billet ready to shape into a knife right away?

A: Yes — the billet has been flat-ground and acid-pickled, making it ready for further shaping, grinding, and profiling. Simply mark out your blade design, cut the profile, grind the bevel, and finish with acid etching to reveal the full Damascus water-wave pattern.

Q: What tools do I need to work with this Damascus steel billet?

A: Basic knife-making tools include an angle grinder or belt grinder for profiling and beveling, files for edge refinement, sandpaper (up to 600-grit or beyond for polishing), an acid solution for etching the pattern, and handle-making materials. A drill press is helpful for adding handle pin holes.

Q: Will the water-wave pattern look the same on both sides of the billet?

A: Due to the nature of multi-layer forging and the segmenting process, the pattern and texture may differ slightly between the two sides. This is a natural characteristic of hand-forged Damascus steel and adds to the uniqueness of each finished blade.

Q: What is the hardness of this billet and why does it matter?

A: This billet is heat-treated to approximately HRC 58 through vacuum deep-cooling. This hardness level strikes an ideal balance — hard enough for excellent edge retention, yet tough enough to resist chipping or brittleness, making it well-suited for functional everyday-carry or kitchen knives.

Production & Packaging Notice

To maintain high stock availability and fast shipping times, our items are sourced from multiple verified manufacturing facilities. While the core quality, materials, and product specifications remain identical, you may notice slight variations in the packaging design, manufacturing origin, or the wording of the printed instructions.